Project Overview

Complete bathroom renovation in a Victorian townhouse requiring careful work around original architectural features. The existing plumbing dated from the 1980s and needed full replacement to meet current standards.

Work Completed

• Removed old bathroom suite and stripped back to bare walls
• Installed new copper pipework throughout with 22mm hot and cold supplies
• Fitted Grohe thermostatic shower system with overhead and handheld options
• Installed Villeroy & Boch wall-hung toilet with concealed cistern
• Added electric underfloor heating system (150W per square metre)
• Upgraded water pressure with Stuart Turner pump (2.0 bar)
• Installed chrome heated towel rail (600mm x 1200mm)
• Fitted extractor fan with humidity sensor

Technical Details

All pipework installed to BS EN 1057 standards with compression fittings. Pressure testing completed at 10 bar for 2 hours with zero pressure loss. Electrical work certified by Part P registered electrician. Waterproofing applied using Mapei tanking system before tiling.

Project Overview

Full commercial kitchen plumbing installation for a new restaurant. Work coordinated with kitchen equipment suppliers and building contractors to ensure all connections met manufacturer specifications and regulatory requirements.

Work Completed

• Installed 1000-litre grease trap system with access chamber
• Fitted stainless steel three-compartment sink (600mm x 600mm each)
• Connected commercial dishwasher with 3/4 inch hot water supply
• Installed gas lines for 6-burner range and combi oven (28mm copper)
• Added pre-rinse spray unit with wall-mounted bracket
• Fitted floor drains with removable grates (4 locations)
• Installed water softener to protect equipment (20-litre capacity)
• Connected ice machine with dedicated water line and drain

Compliance & Certification

All work completed to Building Regulations Part G (Sanitation) and Part J (Combustion appliances). Gas work certified by Gas Safe registered engineer. Grease trap installed to comply with Thames Water trade effluent requirements. Documentation provided for Environmental Health inspection.

Emergency Situation

Homeowner discovered water dripping through ceiling in living room. Burst occurred in 15mm copper pipe in first-floor ceiling cavity, likely due to corrosion at a compression fitting. Water had been leaking for several hours before discovery.

Emergency Response

• Arrived on site within 45 minutes of initial call
• Located and isolated stopcock to stop water flow
• Assessed extent of damage and identified leak source
• Removed ceiling section to access damaged pipe (600mm x 400mm)
• Cut out corroded section and cleaned pipe ends
• Installed new copper pipe section with push-fit fittings
• Pressure tested repair at 6 bar for 30 minutes
• Placed dehumidifier to dry affected areas

Follow-up Work

Returned after 48 hours to verify complete drying and check for any secondary issues. Provided moisture readings and photographs for insurance claim. Recommended inspection of remaining pipework due to age of installation. Total repair time: 4 hours from arrival to completion.

Project Overview

Replacement of 25-year-old conventional boiler system with modern combi boiler. Existing system was inefficient and required frequent repairs. New installation designed to provide instant hot water and zone heating control.

Work Completed

• Removed old boiler, hot water cylinder, and header tanks
• Installed Worcester Bosch Greenstar 30CDi combi boiler (30kW output)
• Fitted 11 new radiators with thermostatic radiator valves
• Installed Nest Learning Thermostat with zone controls
• Upgraded pipework to 22mm for main runs, 15mm for radiator branches
• Added magnetic filter to protect system from sludge
• Flushed system and added inhibitor treatment
• Commissioned system and provided 10-year warranty

Energy Efficiency

New system rated at 94% efficiency compared to 70% for old boiler. Smart controls allow heating schedules for different zones. Estimated annual gas savings of £450 based on current usage patterns. System registered with Gas Safe and Building Control notified as required.

Project Overview

Refurbishment of bathroom facilities across three floors in an office building housing 85 staff. Work scheduled for weekends to avoid disruption to business operations. Focus on water efficiency and accessibility compliance.

Work Completed

• Installed 18 sensor-operated taps (0.5 second delay, 6-litre flow rate)
• Fitted 12 dual-flush toilets (3/6 litre flush volumes)
• Added 6 wall-hung urinals with automatic flush controls
• Created accessible toilet facility with grab rails and emergency alarm
• Installed baby changing station in ground floor facilities
• Upgraded all pipework to copper with isolation valves
• Added thermostatic mixing valves to prevent scalding (43°C maximum)
• Fitted LED mirror lighting with PIR sensors

Compliance & Standards

Accessible facilities designed to Approved Document M standards with 1500mm turning circle and appropriate fixture heights. Water efficiency measures expected to reduce consumption by 40%. All work completed to BS 6700 specification for water installations. TMV2 certified mixing valves installed throughout.

Project Overview

Kitchen plumbing for complete renovation with new layout. Sink relocated to island unit requiring new waste and supply runs. Client requested instant hot water tap and filtered drinking water system.

Work Completed

• Relocated sink position with new 22mm hot and cold supplies
• Installed Quooker boiling water tap with under-sink tank
• Fitted InSinkErator waste disposal unit (0.75 HP motor)
• Added BWT under-sink water filter system
• Connected integrated dishwasher with dedicated supply and drain
• Upgraded waste pipes to 40mm for improved drainage
• Installed isolation valves for all appliances
• Added washing machine connections in utility area

Technical Specifications

Boiling water tap requires 3kW electrical supply installed by certified electrician. Waste disposal unit connected to dedicated 40mm waste with anti-vibration mountings. Water filter system provides 1500 litres before cartridge replacement. All pipework clipped at 500mm centres to prevent noise and movement.